BLDC Three Phase DC Brushless Motor Controller DC 6-60V 400W PWM Hall Motor Control Driver Board With Forward/Reverse/Brake BLDC Three Phase DC Brushless Motor Controller DC 6-60V 400W PWM Hall Motor Control Driver Board With Forward/Reverse/Brake Description: This is a multi-functional three-phase DC brushless non-inductive drive controller with 6 modes and limits, and 3 speed regulation signal inputs. Features: 1. Stable product performance and long service life. 2. Support wide voltage 6-30V, high power 400W. 3. With over-temperature protection, over-current protection, locked-rotor protection, etc. ZS-X11D1 9-60V Specifications: Type: 450W Brushless Hall DC Motor Driver Model Number: ZS-X11D1 Operating voltage: 9-60V Maximum current: rated 16A peak 20A Maximum power: 450W Overcurrent protection: Yes Size: length 63MM* width 45MM* height 28MM Precautions: 1. The power supply circuit on the main board has no fuse, and the built-in self-addition will cause permanent damage to the chip on the board (even 2 seconds is not allowed). 2. During normal operation, there is sampling overcurrent protection at the motor output. Since the module power and current are very large, please do not short circuit when the module is not working normally. Once the short circuit has the possibility of burning the line, the first wiring test machine Please use small current and low voltage test, after ok, then pass high current and high voltage, because it is bare board module for sale, pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts. 3. Do not connect the motor that is obviously inconsistent with the voltage and current of the drive module or is far away from the motor to avoid inexplicable damage. ZS-X14 6-30V Specifications: Type: ZS-X14 Operating voltage: 6-30V(limit 36V) Driving current: rated 18A, plus heat treatment 25A Power: Rated 250W-300W, peak 400W (please leave enough to use) Overcurrent protection: Yes Stoppage protection: Yes (the current automatically drops after stoppage) Over temperature protection: yes (over temperature power halved) Maximum speed: 224000 RPM(2-pole motor), 74000 RPM(6-pole motor), 40000 RPM(12-pole motor), 35000RPM(14-pole motor) 6 mode with limit function Operation instructions: 1. Standard mode stepless speed regulation press to release SET1 forward or reverse to keep SET2 brake to stop at the limit. 2. Automatic mode stepless speed regulation Press SET1 key to start SET2 stop stop by the limit switch to achieve automatic round-trip repeat operation. 3. Point mode stepless speed regulation Press SET1 key forward release stop Press SET2 key reverse release stop meet limit stop. 4. Single round trip mode stepless speed regulation Press SET1 key to start SET2 stop meet limit stop through the limit switch to achieve automatic round trip operation. 5. Single-trigger mode stepless speed regulation Press SET1 key to start SET2 stop meeting limit stop Press SET1 key to start forward meeting limit switch K1 stop again press SET1 key to start reverse meeting limit switch K2 stop. 6. Standard mode level trigger stepless speed regulation press SET1 forward turn once, then press reverse once, then press SET2 brake once, and then press stop limit. 7. In the power motor stop state SET1 SET2 at the same time press the LED flash, you can turn on or off the motor reversing buffer stop braking function. Enter 6 mode switching instructions: 6 mode switching LED flashing definition: slow blinking once standard mode slow blinking twice automatic mode slow blinking three times Point mode slow blinking four times single round trip mode slow blinking five times single trigger mode slow blinking six times standard mode low level triggering, the following is the 6-mode switching operation instructions: First press the SET1 SET2 two keys at the same time and then power on. At this time, the LED flashes and goes out, indicating that it has entered the mode switching state. The LED flashes several times, indicating which mode is currently selected (factory default standard mode), and then short press the SET2 key, the LED flashes and goes out several times. If you want to select the current mode, then long press the SET2 key LED from off to long light to save the current selected mode and automatically exit the mode switch. Enter three kinds of speed control signal switching instructions: Three kinds of speed regulation signal switching LED flashing definition: quick flash once touch analog 1-4.2V (Hall handle required) input quick flash twice PWM input fast flash three times touch analog 0-5V input, the following is the operation instructions into the three kinds of speed regulation signal switching: First press the SET2 key and then power on. At this time, the LED flashes and turns off, indicating that it has entered the speed reg