FrSky Hitec compatible receiver, Minima 4ch

R349.00 3 items in stock
Quantity:
  • Product reference: 4164746-10087035
  • Plane icon Dispatched within 24 hours
  • Shipping from Finland
  • Delivery cost to South Africa R125.88

Hitec A-FHSS compatible receiver. Micro size and suitable for indoor and park fliers. PPM and RSSI output. Range over 300m. 4 Channel Receiver. Hitec 2.4GHz Compatible Thank you for your purchase of this high quality compatible receiver. This receiver has been designed to be a compatible equivalent of the Hitec Minima line of receivers but with an increased specification. As this is compatible with the Minima line of receivers, please ensure that your Hitec 2.4GHz transmitter and/or module support the ability to connect to Minima receivers. For most units, it is likely they have this ability. However for older units, if not already done so, they may need their software updating to support it. If your transmitter or module does not support the Minima receivers, you will need to update its software. This is usually can be done by using a manufacturer’s commercially available PC interface. For more information on this, please contact your local relevant distributor of your transmitter or module and ask for assistance on updating it. Linking the Receiver to your Transmitter Please note that this is only a general procedure. If in doubt, please also refer to your transmitter or module instructions. 1. Put your transmitter into link mode. Usually this is done by pressing the button on the transmitter module and turning on the transmitter. 2. Ensure that your transmitter is in non-telemetry receiver link mode. This can be done by looking on the transmitter module’s status light. If it is flashing Blue, it is in the correct mode. If it is flashing Red, you will need to change mode. To do this, press the button on the transmitter module for around 2 seconds. The status light should change between the two modes. If your module has old software, it may not be able to switch modes. 3. Press and hold the button on the receiver and then power up the receiver. 4. While the receiver is searching for the transmitter module, the Green light on the receiver will flash slowly. 5. Once the receiver is successfully linked to the transmitter module, the Green light on the receiver will flash rapidly. This should only take a couple of seconds and is usually instant. If in doubt, try increasing the distance from the transmitter modules antenna and the receiver. It is recommended to have the receiver between 50cm and 2m away from the transmitter when linking. Setting the Receivers Failsafe By default, if the receiver loses contact with your transmitter it will stop driving the servos and the Red light will flash. If you lose radio contact you may wish to have the servo’s driven to a predefined location. To set this, please follow the instructions below. 1. Ensure that your Transmitter is powered on and transmitting and the Receiver is on and receiving a signal (Red light lit constantly). 2. Ensure that all the transmitter sticks are at the correct locations that you wish to have set up in the event of radio loss. 3. Press and hold the button on the receiver. 4. After 5 seconds the Red light should be lit with the Green light flashing rapidly. 5. Release the button and power cycle the receiver. If you wish to revert to the default mode, simply relink the receiver as in the previous section. PPM and RSSI Output Mode Some advanced users may wish to connect the receiver to specialist devices that take PPM and/or RSSI information. Please ensure that the device supports this mode before operating, as incorrect connections or operation could cause damage and/or physical harm. 1. Put your transmitter into link mode. Usually this is done by pressing the button on the transmitter module and turning on the transmitter. 2. Ensure that your transmitter is in non-telemetry receiver link mode. This can be done by looking on the transmitter module’s status light. If it is flashing Blue, it is in the correct mode. If it is flashing Red, you will need to change mode. To do this, press the button on the transmitter module for around 2 seconds. The status light should change between the two modes. 3. Connect a jumper between the top pins of servo connector 3 and 4. 4. Press and hold the button on the receiver and then power up the receiver. 5. While the receiver is searching for the transmitter module, the Green light on the receiver will flash slowly. 6. Once the receiver is successfully linked to the transmitter module, the Green and Red lights on the receiver will flash rapidly. This should only take a couple of seconds and is usually instant. If in doubt, try increasing the distance from the transmitter modules antenna and the receiver. It is recommended to have the receiver between 50cm and 2m away from the transmitter when binding. Notes: • When the receiver is receiving a signal from the transmitter (i.e. the Red light is lit constantly) in PPM and RSSI output mode, the Green light will also be lit. • The PPM signal is outputted on servo connector 1. • The RSSI signal is outputted on servo connector 2. • Do not connect conventional servos or ESCs to the PPM and RSSI servo connector outputs. Doing so, may burn out and destroy the servo. • Some devices may need a low-pass filter or buffer on the RSSI output. Please consult the devices’ instructions or manufacturer for help or advice on this. • To disable PPM and RSSI output mode, just rebind the receiver as normal.   Notice This unit is not designed, manufactured or supported by Hitec. This third party unit has been designed to be compatible with the Hitec product range of transmitters which may change specification at any time. Any support or assistance required can only be conducted through the original supplier of this unit. This unit is only for remote control of model aircraft, model boats and model cars. As this is an individual part of a system that is integrated by the end user, it is the end users responsibility for the suitability and safety of use of this part. Errors and mistakes by the end user can result in serious personal and third party injury and damage to property outside the control of the manufacturer. Please act responsibly. All trademarks are owned by their respective trademark holders. Hitec is a registered trademark of the Hitec RCD, Inc.

Products are shipped by the individual Fruugo retailers, who are located across Europe and the rest of the world. The delivery times and shipping prices vary depending on the retailer's location, the destination country and the selected delivery method.

Fruugo offers two delivery options: Standard or Express. All retailers offer a standard delivery service, and some retailers also offer an express delivery service.

Although Fruugo retailers endeavour to deliver within these timescales, please note that the above timescales are estimated and not guaranteed.

The delivery timescales do not include any customs clearing times beyond Fruugo's control.

Please allow additional shipping time for deliveries to exceptional locations that are hard to reach, and also during busy periods such as Christmas.

All carriers deliver during normal business working hours and may require a signature on receipt, so please ensure your order is delivered to an address where someone will be available to accept it.

We do our best to ensure that the products that you order are delivered to you in full and according to your specifications. However, should you receive an incomplete order, or items different from the ones you ordered, or there is some other reason why you are not satisfied with the order, you may return the order, or any products included in the order, and receive a full refund for the items.

Certain products purchased at Fruugo cannot be returned. They fall in the following categories:

Please take reasonable care of the goods whilst in your care. Any goods returned must be in a resaleable condition. They must be unworn/unused with original tags attached and in original packaging. It is your responsibility to ensure that the goods are appropriately packaged to ensure they are not damaged in return transit.

Notifying us of a return

If you wish to return an order, or some of the products included in an order, please notify Fruugo customer care within 14 days of receiving the goods, including the following information:

Our customer care will send you specific instructions on how to ship the return package(s) to the retailer(s). Please do not ship the return package before you receive the instructions.

Shipping products back to retailers

Goods must be returned without undue delay and in any event not later than 14 days after notifying us of your cancellation.

If you are returning products to several retailers, you should distribute the products accordingly and send the products to those retailers who shipped them to you initially. 

We strongly recommend that you use registered mail (and insure any high-value packages), since neither Fruugo nor the retailer take responsibility for shipments that are lost or damaged during return transportation.

Please ensure you retain a proof of postage receipt so in the unlikely event your parcel goes missing, you will have proof you sent it.

Refunds

You will be refunded within 14 days of the retailer receiving back the goods. We will notify you by e-mail once the products reach the retailer and are accepted for return. Where a retailer has offered to collect the goods, you will be refunded within 14 days of cancelling your contract.

Unless a product or products you wish to return arrived to you damaged or faulty, you are responsible for the return transportation costs.

Providing you are returning all the products from a specific retailer, we will refund the standard shipping costs you paid for the original delivery. If you chose to pay for a non-standard delivery, we will only refund the cost of our least expensive, standard delivery. 

Damaged or faulty goods

If you receive a damaged, broken, or defective product, please notify Fruugo customer care as soon as possible. Include at least the following information:

We will generally instruct you to ship the damaged product back to the retailer. As soon as it reaches the retailer, they will send you a replacement product. If the replacement can't be made, or if you wish to cancel the order, you will be refunded in full. You will also be reimbursed for reasonable returns postage costs for damaged or faulty goods once we have received your postage receipt.

If the outer packaging of your order is clearly damaged on arrival, and you are suspecting that the products are damaged as well, you can either reject the delivery or accept the goods and sign for them as damaged. In both instances, please notify Fruugo customer care as soon as possible.

Refusing delivery

If you refuse to accept delivery of all or part of your order (where the products or packaging do not appear to be damaged or defective) you will be responsible for the postage charges. Any fees and charges incurred by the retailer due to a package being refused will be deducted from your merchandise refund.

 

More FrSky products